It is CSI’s recommended organization of information within an individual specification section. The consistency introduced by following SectionFormat promotes. About CSI: The Construction Specifications Institute is a professional association MasterFormat,™ SectionFormat™, PageFormat™, UniFormat™, National. Enter CSC/CSI SectionFormat. SectionFormat subscribes to the theory all requirements found in a specification can be organized into one of.

Author: Mazuktilar Yonos
Country: Bahamas
Language: English (Spanish)
Genre: Spiritual
Published (Last): 22 August 2012
Pages: 302
PDF File Size: 11.12 Mb
ePub File Size: 13.26 Mb
ISBN: 294-4-89187-789-6
Downloads: 23318
Price: Free* [*Free Regsitration Required]
Uploader: Yozil

In some cases, the physical frame of the screen can function as a “margin” from the point of view of readability.


Architectural Joint System Schedule: Since there is a need to “address” certain topics in the specification from sectionformst drawings, consistent terminology is used in both documents independently of the numbering scheme. The difference is whether the screen shows bottom and top margins between pages. Mix design or proportioning may be included here or as sectionfotmat characteristic of the product above, under “Description.

Refer to the “Quality Assurance” Article for field samples and mock-ups, which are related to workmanship. The system shall be connected.

BSD – SectionFormat

Describe submittals intended to document the qualifications of entities employed by the Contractor, without repeating the qualifications required. When more than one of the subordinate titles is required, use this Article to categorize the types of references related to the specific section. This Article cei may be retained when more than one of the subordinate titles is used, or this Article title may be omitted and the subordinate title used as a primary Article title.

The term Baseline Schedule, as used throughout the contract documents, shall refer to a fixed projection of the project More information. CSA AM, standard masonry type; clean, dry; protected from dampness, freezing, or foreign matter.


Divisions form the framework for project specifications. The edition is based on broad principles that emphasize readability and ease of navigation for the user. Mortar for Non-load Bearing Walls and Partitions: The general scope, size, format, and quantity of product data submittals are procedural requirements, which should be included in Division Drawings and general provisions sectionformta the Contract, including General and Supplementary Conditions and other Division.

General or typical requirements should be specified in Section Product Delivery Requirements. For door assemblies required 3.

Document General Conditions; Section Warranties. A logical indentation scheme should always be used. Part 1 — General, Part 2 — Products, and Part 3 — Execution and article titles forming the first two outline sectinoformat. This ensures sectionfprmat the page may be identified even if printed pages get separated or if the pages are viewed electronically.

As you can imagine, new titles were added, some were moved from one Part to another, and some were reorganized within the same Part. The written construction documents prepared for procuring a construction contract and for constructing a project.

Furnish and install aluminum architectural storefront system More information. Include statements describing Contractor’s certification of compliance with specification requirements. This estimating guide for repair and remodeling More information. Include sample or actual forms for use during execution of the work. The written construction documents prepared for procurement of a construction contract and for constructing a project.

MasterFormat Division titles appear in the table of contents of a Project Manual as an organizational device and should not be repeated in the specification section headings or within the body of the specifications. The unbound edge margin should range from 13 mm to 20 mm 0.


SectionFormat and PageFormat |

Include information about systems, assemblies, manufactured units, equipment, components, products, materials, and accessories that are provided by the Owner. Cross-referencing here may also be used to coordinate assemblies or systems whose components may span multiple sections and which must meet certain performance requirements as an assembly or system. Feedback after the meeting from group members indicated they liked the idea of splitting the submittals article into Action and Informational.

Anyone wishing the formatting instructions can email me directly to request a copy. Field samples are usually used to state requirements for sample field applications of finishes, or other finish materials and setionformat.

Describe submittal of bonds required by the section, cis repeating the terms of the bond which should be specified elsewhere in Part 1. The use of fanciful fonts for aesthetic reasons is not recommended, as they usually interfere with readability. Spacing Around Nontext Items: Illustrations might not technically relate to Part 2 or Part 3, but may be placed at this location for convenience. Start display at page:. Shop fabrication is preferably stated as a result, but may also include statements of required methods.

May be any one of a number of standard documents published by various professional organizations or provided by the Owner.